What is the process for measuring the hysteresis loop of a material like iron?

Encyclopedia
11/16/2024

Process for Measuring the Hysteresis Loop of Materials like Iron

Measuring the hysteresis loop (Hysteresis Loop) of materials such as iron is an important experimental process used to study the magnetic properties of these materials. The hysteresis loop provides crucial information about energy loss, coercivity, and remanence during the magnetization and demagnetization processes. Below is a detailed procedure for measuring the hysteresis loop:

Experimental Equipment

  • Power Supply: Provides a stable DC or AC power source.

  • Magnetizing Coil: Wrapped around the sample to generate a magnetic field.

  • Hall Effect Sensor: Used to measure the magnetic induction B in the sample.

  • Ammeter: Used to measure the current I through the magnetizing coil.

  • Data Acquisition System: Used to record and process experimental data.

  • Sample Holder: Fixes the sample to ensure its position remains stable.

Experimental Steps

Prepare the Sample:

Secure the test material (such as an iron rod or iron sheet) in the sample holder, ensuring its position is stable.

Set Up the Magnetizing Coil:

Wrap the magnetizing coil tightly around the sample, ensuring it is evenly distributed.

Connect the Circuit:

Connect the magnetizing coil to the power supply and ammeter, ensuring the circuit connections are correct.

Place the Hall effect sensor at an appropriate position on the sample to measure the magnetic induction B.

Calibrate the Equipment:

Calibrate the Hall effect sensor and ammeter to ensure accurate measurements.

Initial Demagnetization:

Perform initial demagnetization of the sample to ensure it is in a zero-magnetized state. This can be achieved by applying a reverse magnetic field or heating the sample above its Curie point and then cooling it.

Gradually Increase the Magnetic Field:

Gradually increase the current I through the magnetizing coil and record the magnetic induction B at each current value.Use the data acquisition system to record the corresponding values of I and B.

Gradually Decrease the Magnetic Field:

Gradually decrease the current I through the magnetizing coil and record the magnetic induction B at each current value.Continue recording the corresponding values of I and 

B until the current returns to zero.

Repeat Measurements:

To obtain more accurate data, repeat the above steps multiple times to ensure consistency and reliability of the data.

Plot the Hysteresis Loop:

Use the recorded data to plot the relationship between magnetic induction B and magnetic field strength H.

The magnetic field strength H can be calculated using the following formula: H= NI/L

where:

  • N is the number of turns in the magnetizing coil

  • I is the current through the magnetizing coil

  • L is the average length of the magnetizing coil

Data Analysis

Determine Remanence Br:

Remanence Br is the magnetic induction remaining in the material when the magnetic field strength H is zero.

Determine Coercivity Hc :

Coercivity Hc  is the reverse magnetic field strength required to reduce the magnetic induction B from its positive maximum value to zero.

Calculate Hysteresis Loss:

Hysteresis loss can be estimated by calculating the area enclosed by the hysteresis loop. The hysteresis loss Ph can be expressed using the following formula: P h =f⋅Area of the hysteresis loop where:

f is the frequency (unit: hertz, Hz)

Precautions

  • Temperature Control: Maintain a constant temperature during the experiment to avoid the influence of temperature changes on the measurement results.

  • Data Recording: Ensure accurate and complete data recording to avoid omissions or errors.

  • Equipment Calibration: Regularly calibrate the experimental equipment to ensure the reliability of the measurement results.

By following these steps, the hysteresis loop of materials like iron can be effectively measured, and important magnetic properties can be obtained. These parameters are crucial for material selection and application.

Encyclopedia

The Electricity Encyclopedia is dedicated to accelerating the dissemination and application of electricity knowledge and adding impetus to the development and innovation of the electricity industry.

What is Automatic Voltage Regulator?
What is Automatic Voltage Regulator?
An automatic voltage regulator is employed to regulate voltage, converting fluctuating voltages into a constant one. Voltage fluctuations mainly stem from variations in the load on the supply system. Such voltage variations can damage the equipment within the power system. These fluctuations can be mitigated by installing voltage - control equipment at various locations, such as near transformers, generators, and feeders. Multiple voltage regulators are often placed throughout the power system t
Edwiin
05/22/2025
What is Static Voltage Regulator?
What is Static Voltage Regulator?
Types of Static Voltage RegulatorThe static voltage regulator is superior to electromechanical regulators in respect of the accuracy of control, response, reliability and maintenance. The static voltage regulator is mainly classified into two types. They are;Servo Type Voltage RegulatorMagnetic Amplifier RegulatorThe types of static voltage regulator are described below in details;Servo Type Voltage RegulatorThe main feature of the servo type voltage regulator is the use of the amplidyne. The am
Edwiin
05/21/2025
What is Arc Extinction Circuit Breaker?
What is Arc Extinction Circuit Breaker?
When the current-carrying contacts of a circuit breaker separate, an arc forms and persists briefly after contact separation. This arc is hazardous due to the heat energy it generates, which can produce explosive forces.A circuit breaker must extinguish the arc without damaging equipment or endangering personnel. The arc significantly influences the breaker’s performance. Interrupting aDC arcis inherently more challenging than anAC arc. In an AC arc, the current naturally reaches zero duri
Edwiin
05/20/2025
Air Break Circuit Breaker
Air Break Circuit Breaker
In an air break circuit breaker, the arc is initiated and extinguished in substantially static air as the arc moves. These breakers are used for low voltages, generally up to 15 kV, with rupturing capacities of 500 MVA. As an arc-quenching medium, air circuit breakers offer several advantages over oil, including:Elimination of risks and maintenance associated with oil use.Absence of mechanical stress caused by gas pressure and oil movement.Elimination of costs from regular oil replacement due to
Edwiin
05/20/2025
Inquiry
Download
Experts Electrical is dedicated to serving the personnel in the global power industry.
Join Experts Electrical, not only can you discover power equipment and power knowledge, but also canhnd like - minded friends!